Deck Pressure Washing Cost (2026): Prices by Size and Material

Trex says you can take a pressure washer to its Transcend and Enhance boards at up to 3,100 PSI, fan tip, eight inches off the surface. TimberTech says a power washer is for rinsing only and caps it at 1,500. The Western Red Cedar Lumber Association says do not power wash cedar at all.

What a deck wash actually sells for in 2026

Median of every published price we could find, computed from the WashNumbers dataset. Accessed August 2026.

Deck and patio jobs, per job

$250
Middle half of the market$175 to $312
Full spread$85 to $1000
Figures behind it24 prices, 15 sources

By area, per square foot

$0.33
Middle half of the market$0.30 to $0.38
Full spread$0.29 to $0.48
Figures behind it5 prices, 3 sources

This is our own figure, not a quote from one publisher. Check every observation behind it.

Three manufacturers, three answers, and every one of them is talking about a deck.

That is the awkward part of deck pressure washing cost. Before anyone can price the job, somebody has to work out whether the job is the right one for your boards, and a quote that never names a method is a quote for an unknown service. There is no universal best PSI for a deck, whatever the first result tells you.

Published prices sit around $100 to $250 for a professional clean. The per-square-foot versions are below, and they disagree with each other by nearly half.

What none of those figures carry is the railing, the stairs, the lattice and the underside of a raised deck. Floor area misses all four, and on a typical elevated deck they are most of the work.

Quick answer

  • Angi currently reports approximately $100–$250 for professional deck pressure washing, with about $150 as its typical figure.
  • Homewyse currently estimates approximately $0.46–$0.57 per square foot under its basic-project assumptions.
  • Fixr publishes approximately $100–$200, with around $145 as its national average reference and approximately $0.30–$0.40 per square foot.
  • The WashNumbers homeowner model currently uses $0.49 per square foot as a transparent deck base-rate assumption before condition, access, the modeled minimum, and the estimate band are applied.
  • Railings, stairs, lattice, detailed surfaces, and the underside of an elevated deck may substantially increase the amount of work even when the deck floor area stays the same.
  • High pressure is not appropriate for every deck material. Manufacturer instructions should take priority over any generic pressure-washing recommendation.

For an estimate based on your own deck size, condition, and access, use the Pressure Washing Cost Calculator.

Pricing references reviewed: August 2026.

Deck pressure washing cost comparison showing two 300 square foot decks with different cleaning scope, material, railings, stairs, access, and condition

What a deck clean actually costs in 2026

Current pricing references do not produce one universal deck-cleaning price.

That does not necessarily mean the sources contradict one another. Their numbers can represent different deck sizes, project assumptions, local markets, labor structures, and cleaning scopes.

Current U.S. deck-cleaning pricing references reviewed by WashNumbers. Sources use different assumptions, so the figures are not directly interchangeable.
Source Published Cost Pricing Basis Source Timing
Angi $100–$250 Professional deck pressure washing; about $150 typical Updated Aug. 3, 2026
Homewyse $0.46–$0.57 / sq. ft. Basic work under favorable stated conditions January 2026 estimate
Fixr $100–$200 $145 national-average reference; also lists $0.30–$0.40/sq. ft. Updated Jan. 31, 2025
HomeGuide $120–$240 About $0.35/sq. ft. plus separate feature references Older editorial reference
WashNumbers model $0.49 / sq. ft. base Transparent modeling assumption before condition and access adjustments Reviewed Aug. 2026

WashNumbers does not average these figures together and label the result a national price.

Instead, the published numbers are used as context, while any WashNumbers-specific rate or adjustment is clearly identified as a modeling assumption.

This distinction is explained in the WashNumbers Methodology.

Deck Pressure Washing Cost by Size

Deck floor area is still a useful starting point when the deck is relatively simple.

The WashNumbers homeowner model currently begins with:

Base deck cost = deck floor area × $0.49 per sq. ft.

For average buildup and normal access, the condition and accessibility multipliers remain at 1.00×.

The model then applies a $100 small-job floor when necessary and shows a planning range of ±20% around the typical modeled estimate.

WashNumbers model using a $0.49/sq.-ft. deck base rate, average buildup, normal access, a $100 modeled minimum, and the default ±20% planning band applied above that minimum.
Deck Floor Area Base Calculation Typical Modeled Estimate Planning Range
100 sq. ft.100 × $0.49 = $49$100*$100–$120
200 sq. ft.200 × $0.49 = $98$100*$100–$120
300 sq. ft.300 × $0.49 = $147$147$118–$176
400 sq. ft.400 × $0.49 = $196$196$157–$235
500 sq. ft.500 × $0.49 = $245$245$196–$294
700 sq. ft.700 × $0.49 = $343$343$274–$412
1,000 sq. ft.1,000 × $0.49 = $490$490$392–$588
*Small-job floor: The WashNumbers $100 modeled minimum controls the typical estimate whenever the raw calculation falls below $100. It also sets the bottom of the planning range on those rows, because nothing can be quoted below the minimum. The ±20% band applies from the minimum upward.

These are WashNumbers planning estimates, not reported national averages or guaranteed contractor quotes.

For comparison, Angi currently publishes approximately $100 for 300 square feet, $200–$300 for 700 square feet, and $300–$400 for 1,000 square feet.

Those published examples let us calculate something useful that is not immediately obvious from the total prices.

What those published prices work out to per square foot

Dividing Angi’s published size examples by their corresponding deck areas gives the implied effective square-foot rate.

WashNumbers calculation of the effective square-foot rate implied by Angi’s published 2026 deck-size examples.
Deck Size Angi Published Cost Calculation Implied Effective Rate
300 sq. ft. $100 $100 ÷ 300 $0.33 / sq. ft.
700 sq. ft. $200–$300 $200–$300 ÷ 700 $0.29–$0.43 / sq. ft.
1,000 sq. ft. $300–$400 $300–$400 ÷ 1,000 $0.30–$0.40 / sq. ft.

This calculation shows why it is risky to take one price-per-square-foot number and apply it universally.

Angi’s own size examples imply an effective rate of about $0.29 to $0.43 per square foot across the examples above, depending on deck size and where the project falls within the published range.

That still does not mean $0.29–$0.43 is the “correct” national rate. It is simply what those specific published examples imply mathematically.

For a wider explanation of how square-foot pricing works across exterior-cleaning surfaces, see the Pressure Washing Cost per Square Foot Guide.

What the decking material does to the price

Material can change both the potential price and the appropriate cleaning process.

Angi currently publishes the following examples for a 300-square-foot deck:

Metal: approximately $100

Composite: approximately $100–$150

Wood: approximately $100–$200

Converted into effective rates, those examples correspond to roughly:

Metal: $0.33/sq. ft.

Composite: $0.33–$0.50/sq. ft.

Wood: $0.33–$0.67/sq. ft.

But price is only half of the story.

The more important question is whether the specific decking product should be cleaned with substantial water pressure at all.

No, not every deck should be pressure washed

“Deck pressure washing cost” is a useful search and pricing term, but it should not be interpreted as a recommendation to use high pressure on every deck.

Manufacturer guidance varies substantially even between products that homeowners may broadly describe as composite decking.

Examples of current manufacturer or industry guidance. Always check instructions for the exact decking product before cleaning.
Deck Material / Product Pressure-Washer Guidance Key Limit Why It Matters
Trex Transcend, Enhance & Select Permitted under Trex’s specified procedure ≤ 3,100 PSI Fan tip; keep at least 8 in. from surface and follow Trex cleaning instructions.
TimberTech Power washer for rinsing only ≤ 1,500 PSI Use a fan-tip nozzle and spray with the grain pattern.
Pressure-treated wood Very cautious use; experienced users or professionals recommended < 500 PSI Excessive pressure can damage and roughen wood fibers.
Western Red Cedar Power washing not recommended Avoid Real Cedar warns that power washers can seriously damage cedar surfaces.

Trex Composite Decking

Trex states that a pressure washer of no more than 3,100 PSI may be used for dirt or mud on its Transcend, Enhance, and Select composite decking when the specified procedure is followed.

Its guidance calls for a fan tip, soap and brushing, thorough rinsing, and keeping the fan tip at least 8 inches from the decking surface.

That guidance applies to the products Trex identifies. It should not be treated as a universal rule for every composite deck.

TimberTech Decking

TimberTech provides materially different instructions.

Its current guidance says a power washer may be used for rinsing only, with a recommended maximum of 1,500 PSI, a fan-tip nozzle, and spraying in the direction of the grain pattern.

That difference between two major manufacturers is a good example of why the material name “composite” alone is not enough information to select a cleaning method.

Pressure-Treated Wood

Treated Wood’s deck-care guidance is considerably more conservative.

Its FAQ recommends limiting pressure-washer use to experienced users or professionals and keeping the pressure below 500 PSI, using a fan tip and maintaining appropriate distance from the wood.

Improper pressure can damage wood fibers, leaving visible etching, fuzzing, or splintering.

Western Red Cedar

Western Red Cedar requires even more caution.

The Western Red Cedar Lumber Association states that power washers can seriously damage cedar deck surfaces and does not recommend power washing cedar decks.

A contractor evaluating a cedar deck may therefore recommend an alternative cleaning method rather than simply lowering or raising the pressure-washing price.

Your floor area leaves out the railings and the stairs

Floor area describes the walking surface. It does not describe the railing, and on a raised deck the railing is where the hours go.

This is something worth confirming when comparing contractor quotes.

HomeGuide, for example, publishes separate pricing references for several detailed deck components:

Examples of separately published deck-component pricing from HomeGuide. Contractors may structure quotes differently, so these figures should not automatically be added to every project.
Additional Deck Feature Published Reference Pricing Unit Why Floor Area Misses It
Stairs $65 Per staircase Treads, risers and edges add detailed cleaning.
Handrails $2.50–$3.50 Per linear foot Rails and balusters are not represented by floor square footage.
Lattice $0.85–$0.95 Per sq. ft. Detailed vertical surfaces add additional cleaning scope.
Deck underside $1.50 Per sq. ft. An elevated deck can expose substantial additional surface area.

These figures should not automatically be added to every deck estimate.

Some contractors may include certain features within a flat project price, while others may price them separately. The figures are useful because they demonstrate that floor area is not the only measurable part of the cleaning scope.

When requesting quotes, clarify whether the price includes:

deck boards, railings and balusters, posts, stair treads and risers, lattice or skirting, fascia, and the underside of an elevated deck.

Comparing two totals without confirming the included surfaces can make one contractor appear much more expensive even when the scopes are different.

Decks are not the only surface where the headline measurement hides the work. Patios have the same problem with joint sand and pavers, which our patio pressure washing cost guide goes through, and fences have it worse, because the same linear footage can mean one side or two, as the fence guide explains. If you want to compare quotes properly across any of these surfaces, the cost per square foot guide is where we set that out.

How we build the number

The current WashNumbers model uses a transparent $0.49 per-square-foot deck base rate.

The basic formula is:

Base cost = deck floor area × $0.49

The model then adjusts that result for project condition:

Light buildup = 0.90×

Average buildup = 1.00×

Heavy buildup = 1.15×

and accessibility:

Easy access = 0.95×

Normal access = 1.00×

Difficult access = 1.10×

The resulting formula is:

Typical modeled estimate = base cost × condition factor × access factor

The model also uses a $100 small-job floor and a ±20% planning band.

These percentages are WashNumbers modeling assumptions. They are not presented as contractor industry standards.

Example: 400 Sq. Ft. Deck

For a 400-square-foot deck with average buildup and normal access:

400 × $0.49 = $196

Condition:

$196 × 1.00 = $196

Access:

$196 × 1.00 = $196

Typical modeled estimate:

$196

Planning range:

$157–$235

That result is also generated by the current Pressure Washing Cost Calculator.

Example: 400 Sq. Ft. Deck With Heavy Buildup and Difficult Access

Using the same 400-square-foot deck:

400 × $0.49 = $196

Heavy-buildup adjustment:

$196 × 1.15 = $225.40

Difficult-access adjustment:

$225.40 × 1.10 = $247.94

Typical modeled estimate:

approximately $248

The ±20% planning band produces approximately:

$198–$298

The model is designed to demonstrate how size, condition, and access interact. It cannot determine whether a deck requires specialized restoration, hand cleaning, repair work, or a different cleaning method.

Measuring a deck without getting it wrong

For a simple rectangular deck:

Length × width = deck floor area

For example:

20 ft × 15 ft = 300 sq. ft.

For an L-shaped or irregular deck, divide the floor into smaller rectangles, calculate each section, and add the results.

Do not automatically assume the floor-area calculation represents the entire cleaning scope.

Record additional features separately, including approximate railing length, number of staircases, lattice or skirting, and whether underside cleaning is requested.

This gives a contractor far more useful information than simply saying, “I have a 300-square-foot deck.”

What goes wrong when you do it yourself

DIY cleaning can reduce labor cost, but decks are less forgiving than many concrete surfaces.

Incorrect nozzle choice, excessive pressure, inconsistent wand distance, or cleaning across the grain can permanently mark some materials.

Homeowners should identify the exact deck material and, where possible, the manufacturer before deciding on a cleaning method.

If the surface has loose boards, rot, splintering, failed coatings, severe weathering, or uncertain material, an inspection may be more useful than immediately pressure washing it.

A professional quote should also explain what method is being used, not simply provide a dollar amount.

Pressure washing does not repair structural or surface deterioration.

Loose boards, protruding fasteners, significant rot, unstable railings, severe splintering, or damaged composite boards may require attention before aggressive cleaning.

A contractor may also adjust the cleaning method around weak areas to avoid making existing damage worse.

This is another reason the lowest quote is not automatically the best comparison.

The important question is whether every quote covers the same scope using an appropriate method for the actual deck.

Deck Pressure Washing Cost FAQ

How Much Does It Cost to Pressure Wash a 300 Sq. Ft. Deck?

Angi currently publishes approximately $100 as its size example for a 300-square-foot deck.

The WashNumbers model uses $0.49 per square foot, producing:

300 × $0.49 = $147

With average buildup and normal access, the modeled typical estimate is $147, with a planning range of approximately $118–$176.

Actual quotes can differ depending on material, railings, stairs, condition, access, location, and contractor minimums.

How Much Does It Cost to Pressure Wash a 500 Sq. Ft. Deck?

At the current WashNumbers modeled base rate:

500 × $0.49 = $245

For average buildup and normal access, the typical modeled estimate is $245, with a planning range of approximately $196–$294.

This is a model calculation rather than a reported national average.

How Much Does It Cost to Pressure Wash a 1,000 Sq. Ft. Deck?

Angi currently publishes approximately $300–$400 for its 1,000-square-foot example.

The WashNumbers model produces:

1,000 × $0.49 = $490

with a default planning band of approximately $392–$588 before accounting for unusual scope or material-specific cleaning requirements.

The difference illustrates why WashNumbers shows its assumptions instead of describing the model output as the national price.

How Much Does Deck Pressure Washing Cost per Square Foot?

Current references differ.

Homewyse currently publishes approximately $0.46–$0.57 per square foot, while Fixr publishes approximately $0.30–$0.40 per square foot.

HomeGuide publishes approximately $0.35 per square foot for deck power washing, although its visible editorial date is older than the 2026 Angi and Homewyse references.

WashNumbers currently uses $0.49 per square foot as a model assumption, not as a claimed U.S. average.

Does Deck Pressure Washing Include Railings?

Not automatically.

Contractor scopes differ. Ask whether railings, balusters, posts, stairs, fascia, lattice, and the underside are included before comparing quotes.

Can You Pressure Wash a Composite Deck?

It depends on the exact product.

Trex permits pressure washing on specified products under its stated limits, while TimberTech says a power washer should be used for rinsing only and sets a lower maximum recommended pressure.

Check the manufacturer’s instructions for the specific decking product.

Can You Pressure Wash a Wood Deck?

Some wood decks can be cleaned using carefully controlled low pressure, while other wood products should not be power washed.

Treated Wood recommends very low pressure and experienced use for pressure-treated decking, while the Western Red Cedar Lumber Association does not recommend power washing cedar decking.

Identify the material before selecting the cleaning method.

Is It Cheaper to Pressure Wash a Deck Yourself?

DIY work eliminates professional labor charges but may still involve equipment rental, cleaning products, preparation time, and the risk of surface damage.

The safest economic comparison should consider both direct cost and whether the homeowner has the equipment and experience required for the specific deck material.

What this model does not know about your deck

WashNumbers compares published U.S. pricing references with transparent planning models.

External source figures remain identified as published data.

The current $0.49 deck base rate, condition multipliers, accessibility multipliers, $100 modeled minimum, and ±20% estimate band are WashNumbers assumptions used to create a reproducible planning estimate.

They are not presented as universal contractor pricing rules.

The full formulas, model assumptions, limitations, and source-selection approach are documented in the WashNumbers Methodology.

The estimates on this page are intended for budgeting, education, and quote comparison.

Only a contractor evaluating the actual deck can provide a project-specific price and determine an appropriate cleaning method.

Pricing references last reviewed by WashNumbers: August 2026.

Sources

Work out your own number

Pressure Washing Cost Calculator
Put in your own square footage and surface instead of using an average.

Cost per Square Foot
What the rate should be before anyone quotes you a total.

Minimum Charge Explained
Why a small job costs the same as a slightly bigger one.

The Pricing Dataset
220 published prices with the source behind every figure.

Written by Diego Hernández, founder of WashNumbers. Cost models are built from published contractor rates and public price observations. See how we build these numbers.

Last reviewed: October 2026